Flooring July 24, 2017. With reclaimed material waste factor is a huge variable. How much effort does the manufacturer take to give you a 100% usable product? Poorly milled with very little defecting and culling done on a solid wood floor that costs $6/sf and has a 15% waste factor actually costs more than a similar product that is milled better costing $7/sf with a 2% waste factor. That extra wastes costs more in shipping and labor to defect. This is one of the hardest things to demonstrate to a customer that the face value costs doesn`t necessarily represent the actual raw material cost unless one is truly comparing identical quality and specified products.
Flooring July 23, 2017. One drawback is that this type of floor requires special hanger systems designed for the joists, to enable them to be hung from each other or against beams/bearing walls. Manufactured joists are becoming a popular flooring system, for they are relatively cheap, reduce labour time and provide adequate support. However, builders need to familiarize themselves with its installations, for poor installation can cause severe structural damage to the joists. A good example is a three point, center bearing joist, left with the top chord uncut, which can potentially fail or pull apart, over the center bearing point.
Flooring July 17, 2017. In this article we will be discussing several different categories of wood flooring. Solid wood flooring is one board with no glued up laminations; it is basically wood board that has been sized and profiled to a certain dimension. Engineered flooring has a on the top whatever species and texture you want, and this is glued to a plywood backer on the bottom. Engineered is still all wood but is made with multiple layers that are laminated for better stability and dimensional accuracy. Floors that we will not cover here are laminates or any composite products which are often not wood entirely through the plank or may be made with a photo printed surface. We also will not cover vinyl, carpet, stone, or tile.
Flooring July 23, 2017. Traditional tile installation requires many tools and lots of patience which have to be pre-set on the floor, cut down to size, then adhered to the floor using a strong industrial glue. They will not stick to every surface and frequently, a layer of floor base must be installed before the tiling work can begin. If the tiles are placed too close together, they can buckle, leaving unsightly bumps and lumps on the floor. If they are placed too far apart, there will be obvious gaps. If a mistake is made when laying down the tile, it is very difficult to fix as the tile is glued to the floor. The tile will have to be pried up, excess adhesive scraped, and the process started over. Laying traditional tile floors is a project that can take several days, to several weeks, to finish.
Flooring July 24, 2017. The third variable is installation costs. Our engineered product has labor savings over our solid wood product because it is pre-sanded and milled to tighter tolerances. It is also prefilled in the holes and has next to zero waste. On the other hand you may have a little more in cost of gluing it down in addition to nails, but this is just a step in direction of better quality and peace of mind during the install.
Flooring July 24, 2017. This shrinking action pulls the floor together, adding strength to the overall system. The advantages of this type of sub-floor are its strength and durability. One important note, homeowners are often disturbed by the small 1/4" wide gaps, generally left between the individual planks after the wood dries out. Although disturbing to see during construction, upon completion, the spaces are not noticeable, and really have no impact on the sub-floor components at all. Strip floors are designed to be interlocking, through lapping or spacing of joints.
Flooring July 24, 2017. Raw sheathing comes in 4`x8` sheets, most often installed as 3/4" thick plywood panels. This type of sheathing is adequate for spanning joist work spaced up to 24" apart. The sheathing is lain with the joints staggered in such a matter, that no two edge joints line up with adjoining sheets. It is very easy to install, requiring the least amount of labour. The sheets are fastened with either 1-1/2" flooring screws, or 2-1/2" nails, spaced about 8" apart. Although not required, it is a good idea to provide backers or supports under the joints, between sheets which run perpendicular to the framed floor assembly.
Flooring July 24, 2017. Here is a word on prefinished product if they factor into your decision. If you come up short on your order, the next lot that you buy may not match your previous batch. This is especially a problem on the lower end price floors and import floors. Good luck trying to blend it in with your previous floor. So if you go this route, be extra accurate on your measurements. Right now the rage is lifetime warranties on flooring. We stop to think is that really even possible? First will that importer or manufacturer really be around a lifetime? A lot of products are made oversees; the warranty is only good if there is somebody still around for the life of the warranty.
Flooring July 12, 2017. In this article we will be discussing several different categories of wood flooring. Solid wood flooring is one board with no glued up laminations; it is basically wood board that has been sized and profiled to a certain dimension. Engineered flooring has a on the top whatever species and texture you want, and this is glued to a plywood backer on the bottom. Engineered is still all wood but is made with multiple layers that are laminated for better stability and dimensional accuracy. Floors that we will not cover here are laminates or any composite products which are often not wood entirely through the plank or may be made with a photo printed surface. We also will not cover vinyl, carpet, stone, or tile.