Flooring June 15, 2017. In the case of long span truss work, bearing lengths of at least 3" are quite common. Trusses span greater distances than framed floor assemblies and can be designed to span the entire building, eliminating center load bearing supports. They are moderately more expensive than framed floor assemblies, but provide a remarkably strong floor with little deflection or "bounce" to it. Another advantage to this type of structural system, is that utility installations can be run between the webwork components. Never allow trades to cut or drill into the members of a truss, for they are manufactured precisely for the loading conditions they will undergo during the life of the building.
Flooring June 14, 2017. Another good flooring for wet areas is the vinyl tile. Typically it is manufactured in much the same way as sheet vinyl, but is much more rigid and comes as 12"x12" square units. They are installed in the much the same way, but require skilled tradesmen, familiar with proper installation. A good installer will start from the middle of the room to ensure that all cut tiles are equal in width at opposing walls. One advantage to this type of flooring, over sheet vinyl, is that it is can be installed, without danger of joint separation, over large areas. For this reason, it is often used in commercial buildings where large rooms are the norm. Vinyl tile can also be easily installed directly to concrete floors. Like vinyl sheets, it too is resistant to water, and tends to be installed in the areas of a building, prone to water accumulations. Tile, can be easily cleaned, is relatively maintenance free, and one of the cheaper finished floors to install.
Flooring June 11, 2017. Carpet is probably the most common floor covering that is used in residential homes. It comes in a wide variety of colors and textures. Carpet consists of woven fibers, which protrude upwards, glued or woven into a foam or jute backing. Often an underpad of pressed foam is installed below it or the backing can be integral with the carpet, adding to the softness and providing a much more comfortable surface for walking on. Carpet is installed by either gluing the carpet to the sub-floor, or the use of carpet tack around the perimeter. A good carpet will has a close weave, which will not show the backing material when separated. To reduce project costs, some contractors will opt to install a high quality underlay, with a low or medium quality carpet. This provides the soft surface, with equal durability, giving the homeowner the benefits of high quality carpet, at a reduced cost.
Flooring June 22, 2017. Traditional tile installation requires many tools and lots of patience which have to be pre-set on the floor, cut down to size, then adhered to the floor using a strong industrial glue. They will not stick to every surface and frequently, a layer of floor base must be installed before the tiling work can begin. If the tiles are placed too close together, they can buckle, leaving unsightly bumps and lumps on the floor. If they are placed too far apart, there will be obvious gaps. If a mistake is made when laying down the tile, it is very difficult to fix as the tile is glued to the floor. The tile will have to be pried up, excess adhesive scraped, and the process started over. Laying traditional tile floors is a project that can take several days, to several weeks, to finish.
Flooring June 17, 2017. Let`s move onto another reason why engineered wood flooring is now classed as a superior product to a solid oak floor. The main reason why people will go for an oak floor is that they love the timeless natural beauty that European oak has to offer. What many people are unaware of is the fact that the top layer of a good engineered oak flooring is the same quality European oak as you would find in solid oak flooring. This means that when it has been laid it looks and feels just the same and more and more customers are saying they prefer the look of the longer and wider boards that many engineered wood floors offer.
Flooring June 13, 2017. One drawback is that this type of floor requires special hanger systems designed for the joists, to enable them to be hung from each other or against beams/bearing walls. Manufactured joists are becoming a popular flooring system, for they are relatively cheap, reduce labour time and provide adequate support. However, builders need to familiarize themselves with its installations, for poor installation can cause severe structural damage to the joists. A good example is a three point, center bearing joist, left with the top chord uncut, which can potentially fail or pull apart, over the center bearing point.
Flooring June 08, 2017. Ceramic tile is probably the most durable types of flooring and is typically installed in entry areas, where sand scuffing and water accumulations are the norm. Bathrooms and kitchens often get this type of floor treatment as well, but due to the high cost of installation, homeowners tend to not include these areas. Ceramic tile are typically a square tile, although interlocking units are on the market, in standard square measurements of 4", 6",8" or 12". They are installed by one of two primary methods, either set into a thin mortar bed (called "thinset adhesive"), which also acts like glue, or a heavyset bed of 1-1/2" normal mortar base. For all ceramic tile installations, the floor must be built up to ensure the strength required to prevent tile or joint cracking. Often, installers put down a material called "cement board", which is much like drywall, but is made of glass fibers and cement. In any case, ensure that your installer will offer you a guarantee against future cracking or uplift of tiles. Ceramic tiles require little maintenance, but beware, water on glossy floor tiles can be very slippery, and many a time, a homeowner has resented the installation of a high gloss tile, over a bathroom floor area.
Flooring June 10, 2017. Of all the wood flooring, the most often installed is the parquet tile. They consist of square interlocking wood strips, held together with glues and/or metal wires. Often they come as single 6"x6", or multiple 12"x12" square tiles, about 1/4" thick. They are glued directly to the sub-flooring, and are strong enough to span small deviations in it. The wood is often prefinished, and requires little maintenance. Parquet floors are a cheaper alternative to strip flooring, providing the same warm, durable surface.